Short answer: a stable liquid humate is made by dissolving a fully soluble potassium humate (or fulvate) in water at a suitable concentration, keeping the pH alkaline for humates, avoiding calcium and acid, and filtering or settling out any insoluble residue. Most stability problems come from hard water, low pH, too high a concentration or mixing with incompatible products.
Basic recipe for a stock solution
- Start with clean water; soft or low-calcium water is best.
- Add potassium humate powder or flake slowly while stirring.
- Stir until dissolved; warm water speeds this up.
- Let stand and check for sediment; filter or decant if needed.
- Store in a closed, opaque container; label with date and concentration.
What makes a liquid humate unstable
| Cause | What you see | Fix |
|---|---|---|
| Hard water (calcium, magnesium) | Flocs and sediment | Use softer water or a fulvate grade |
| Low pH (acids, acidic fertilizers) | Dark precipitate, separation | Keep humate solutions alkaline or switch to fulvic acid |
| Too high concentration | Gel-like, hard to pump | Dilute; check viscosity |
| Insoluble residue in raw material | Sludge at the bottom | Use fully soluble grades; filter |
| Contamination and long storage | Odour, mould at surface | Clean containers; use within a reasonable time |
Humate or fulvate for liquids?
| Property | Potassium humate | Potassium fulvate / fulvic acid |
|---|---|---|
| Solution pH | Alkaline (9–10) | Depends on grade (4–6 or 9–10) |
| Hard-water tolerance | Lower | Higher |
| Mixing with acids | Precipitates | Possible with low-pH grades |
| Cost per unit humic material | Lower | Higher |
Using liquid humate
- Fertigation: inject separately from calcium nitrate and acids.
- Soil drench: apply to moist soil around the root zone.
- Foliar: use low concentrations and check compatibility; fulvic grades are usually preferred.
- Seed or transplant: low-concentration solution at establishment.
Grades suited to liquids
| Grade | Code | Water solubility | pH (1:100) |
|---|---|---|---|
| Potassium humate powder | SH-KH-02P | 100% (dry basis) | 9.0 – 10.0 |
| Potassium humate flake | SH-KH-04F | 100% (dry basis) | 9.0 – 10.0 |
| Potassium fulvate grade 1 | SH-KF-01P | 100% (dry basis) | 4.0 – 6.0 |
| Mineral source potassium fulvate | SH-FA-02P | 100% (dry basis) | 9.0 – 10.0 |
Typical values from Saint Humic Technical Data Sheets, version 1.0; not a specification. Batch results are given on the Certificate of Analysis. Application rates depend on crop, soil and formulation; contact us and run a small trial before large-scale use.
Key takeaways
- Use fully soluble grades, soft water and alkaline conditions for humate liquids.
- Switch to fulvic grades for hard water, acidic mixes and foliar use.
- Jar-test before mixing and store solutions closed and labelled.
Shelf life and storage of solutions
- Concentrated alkaline humate solutions are relatively stable when kept closed.
- Dilute solutions are best used soon after mixing.
- Keep containers out of direct sun and frost.
- Stir or shake before use if slight settling occurs.
Equipment care
Humate solutions are dark and can stain tanks, hoses and nozzles. Flush equipment with clean water after use, especially before using the same equipment for acidic or calcium-containing products, where residues could precipitate.
Frequently asked questions
How do I make liquid humate?
Dissolve fully soluble potassium humate in soft water, let stand, and filter if needed.
Why does my liquid humate form sludge?
Usually hard water, low pH or insoluble residue in the raw material.
Can liquid humate be sprayed on leaves?
At low concentration with compatibility checks; fulvic grades are usually easier.
Related Saint Humic pages
References
- Stevenson, F. J. (1994). Humus Chemistry: Genesis, Composition, Reactions (2nd ed.). Wiley.
- Canellas, L. P., Olivares, F. L., Aguiar, N. O., Jones, D. L., Nebbioso, A., Mazzei, P., & Piccolo, A. (2015). Humic and fulvic acids as biostimulants in horticulture. Scientia Horticulturae, 196, 15–27.






